Thank you for visiting SonicWall Community. Configuring access to server behind a SonicWall from WLAN zone to LAN The IP you use doesn't have to be the official IP address of your WAN interface on the Sonicwall. Welcome to the Snap! For more information, please see our BGW320-500 Bridge Mode and/or IP Passthrough Question In some ways this is logical, in others this is a highly frustrating place to hide functionality like this. I'm guessing I need to do some sort of 1-to-1 NAT here, but I'm not sure how it should be configured on the port side to do a direct passthrough without having any sort of interference from the Sonicwall's security. rev2023.5.1.43405. Later, I noticed this a few times. Then you can use that AO to route to wherever you put your internal server. Showing Content for | Change your ZIP Code, Enter another ZIP to see info from a different area. The X1 interface IP of the firewall for this example will be 10.10.10.10. Unexpected uint64 behaviour 0xFFFF'FFFF'FFFF'FFFF - 1 = 0? Usable Public IP range: 0.0.0.2 - 0.0.0.5 Sonicwall TZ190 in place, runs DHCP, hands out 172.16.233.100-200 WAN interface of TZ190 is 0.0.0.2 I have an internal device that has to utilize one of the public IP's (0.0.0.3). I've tried in vain to set it up myself but I've never done it before on a sonicwall so I'm obviously doing things wrong. As soon as I dropped X2, I was smooth sailing. I like to do things right from the start. Network Engineering Stack Exchange is a question and answer site for network engineers. Without the right model of gateway, AT&T tech support was seeing the outgoing IP change when someone was requesting resources from one of my public-facing servers. I got 5 usable addresses from AT&T in the same subnet. Imagine a NSa 2650 network in which the primary LAN subnet is 10.100../24 and the primary WAN IP is 3.3.2.1 while the server's IP address is 192.168..254 in your DMZ zone. I'm going to go out on a limb and say no. Copyright 2023 SonicWall. I am going to pass this along to the person at my office that works on my sonicwall device. Which language's style guidelines should be used when writing code that is supposed to be called from another language? If you really want to do it, there are documents describing how. Consumer Routers cannot handle having two different WAN-side IPs nor two different LAN IPs. In the mean time, I'm having to use AT&T DSL. Definitely, hairpin routing is not the best choice. I want to pass one of the available static IPs I have through MY TZ500 so that I can plug the 2nd TZ500 into one of the free ports on MY TZ500 and have the inside unit use that static IP for the WAN connection - in other words, no double NATing. John, AT&T Community Specialist 0 0 Other devices connected to your gateway may no longer be able to share files with the device in passthrough mode. Let say for example, WAN Interface - 100.100.100.1/24 - L3 DMZ Interface - 100.100.100.1/24 - Transparent LAN Interface - 10.10.10.1/24 - L3 Welcome to another SpiceQuest! All our employees need to do is VPN in using AnyConnect then RDP to their machine. Most of the newer gateways CANNOT provide this type of functionality. @Integra you can add the IP from the supplier to the VPN access tab of your users/groups and with adding a Firewall Rule VPN -> WAN you can allow the access. I ended up doing a splice. Does a password policy with a restriction of repeated characters increase security? Manage your small business voice, data, wireless, TV and IP-based products and services. They have an FTTP Internet circuit with a block of 8 static IP's which we're connecting to with PPPoE to the NTU. You DO NOT normally want to mix IP Passthrough and Public Subnet to the same Router. In this series, we call out current holidays and give you the chance to earn the monthly SpiceQuest badge! You only need to configure one X1 interface and use the 255.255.255.248 subnet. By clicking Post Your Answer, you agree to our terms of service, privacy policy and cookie policy. Previously in my Sonicwall this was referred to as "Transparent IP Mode (Splice L3 Subnet)". ( edited) 0 1 S seegem New Member 67 Messages 2 years ago Got it, thank you. Sonicwall TZ100 Public IP Passthrough - The Spiceworks Community The information you will need will be under the instructions for Motorola NVG 510 and 589 in the article we provided. General Networking. Thanks for your confirmation. Welcome to another SpiceQuest! Your daily dose of tech news, in brief. Copyright 2023 SonicWall. My end goal is to connect one of the static IPs to my Sonicwall firewall/vpn. For this example I'll give the public IP an address of 12.12.12.12. Configure the second WAN IP on the second/temp sonicwall and you are all set. Is that correct? sonicwall - Sonic OS -- How to properly use multiple external IPs Login to the SonicWall GUI. [SOLVED] Passthrough networks site to site vpn - The Spiceworks Community Or is this block just wasteful allocation? into a public object if you wish to talk to the public IPs from the I'll see what I can find out. Ive done a lot to get things to normal but theres a long way to go still. really running on a private side server 10.100.0.2. From your post, in short what I understand is, you have 5 pack of static IP's from AT&T and you need help assigning these IP address on the SonicWall for Internet access. By rejecting non-essential cookies, Reddit may still use certain cookies to ensure the proper functionality of our platform. If you have more WAN static IPs, just add a WAN switch (just a regular switch) between your ISP equipment and the main TZ. Access a server behind the SonicWall from internal networks using Traffic on the inside to the inside should use inside addressing, not the outside addressing. Use an Interface for Public IP Address Passthrough My home network's core is all enterprise equipment and it's cost me less than $500 total. But I've never had a block of IPs before, so would I need a completely separate router to utilize another? It only takes a minute to sign up. What I would like to do is have the UTM pass a public IP through to a second router. Directly connecting your laptop has nothing at all to do with IP Passthrough. The Sonicwall itself will be assigned one of the IPs, and they want to feed another client a port off of the Sonicwall with another of the public IPs. The supplier will see the IP of your VPN gateway. We currently have our main campus connect currently via Unifi airfiber to a branch location down the street (not possible to run cable or fiber), Recently ATT installed Fiber into the branch location for us and we have the service working but not being used at this time, The project would be to connect a vpn switch (like the tp-link safestream vpn) at the branch and connect it over the internet using site-to-site vpn to our main campus sonicwall.